1) Read through "List" of Modules in your Vehicle, HOWEVER Launch X431 does that, and. 2) LIST all Modules shown, and status of each (No faults, 'x' faults, etc.), with particular attention to: 3) Whether or NOT Status of KOMBI, DSC & IHKA Modules is shown, & if so, list of ALL fault codes in each.
Clean the plug and get rid of the cover. Find the water leak that caused the issue. The one I had was leaking tail light gaskets. The tail lights had water in them. When I grabbed the connector the turn signals starting working on the cluster and everything else that was inop.
bimmerlyf Discussion starter. 6 posts · Joined 2016. #1 · Apr 28, 2016 (Edited) PLEASE somebody HELP me.. I have a BMW 320i E46 2004 and the indicator lights have just stopped working the dash indicators don't work either, the globes do not flash and if i press the hazard lights nothing happens. normal lights come on but high beam also not
To roll up the windows it must be done via the driver's door lock. * No high beam indicator though they work. * No seatbelt or light on chime. * Interior light do not turn off when the motor comes on. They have defaulted to the timer of when doors were closed. * Interior lights do not come on when motor is shut down.
With the ignition on, browse your dashboard menu using the left stalk until you see “CHECK.”. Press the BC button to select the “CHECK” menu. A warning icon will be displayed on the upper dashboard screen. Continue scrolling using the left stalk to check for other warning icons. It should be clear what the problem is.
Here are what my symptoms where and what I did to fix it: Symptoms. * Speedo, Tach, Gas, Coolant Temp, MPG, Odo, gauges not working. * None of the steering wheel buttons are working. * Turn signals not working. * Fan works but A/C does not. * Radio works. * ABS and Seat Belt lights work. * Instrument cluster lights up.
Eg. I'm turning right with my indicator on, if I click right again, it turns the indicator off. Saves sometimes clicking left to turn it off and it ends up indicating left! Also I have it set to 3 blinks so when I half depress the switch (ie. Not all the way down), it will blink 3 times and stop. Mainly used changing lanes.
It came on when I started the car this evening. Red headlight icon next to an icon of the car (car icon like the one that warns you when a door is not fully closed). I checked and the tail lights and turn signals all work. Red headlight icon went out about 1 mimute after putting the car in gear. Any ideas?
1. Inaccurate oil reading. The oil level sensor will alert the driver that the engine is low on oil inside the crank case. However, when the sensor is damaged, it may trigger this information inaccurately. Most car owners will check their oil level manually after the alert is indicated on the dashboard. If they check the oil on the dipstick and
Since it is solid, I'd think this could either indicate a problem with the security system, or it needs to be reset. Most security systems will reset if you get out of the vehicle with all the doors closed, then lock/unlock using one of your master keys (not the key fob). I don't know if this will work in this situation, but it's worth a try.
If one or both of your tail lights and turn signals in the back don't work or sometimes don't work you may have the common problem of a bad ground.
Not effected and working fine:-. Xenon Headlights. Interior lights - Door Lights / Reading Lights / Courtesy lights / Vanity Lights. Sometimes during the flickering issue when turn car off brake lights turn on and stay on. Only temporary solution I have found is removing negative cable from battery for a while may solve this.
The turn signals all started working again after a few miles. This past week, the alternator died. My indie BMW shop replaced the alternator with a remanufactured Bosch unit, replaced the related pulleys, tensionors, etc and the car ran fine. The next day, my turn signals (and emergency flashers) stopped working during a 2 mile trip to lunch.
132 posts · Joined 2011. #1 · Nov 11, 2019. The front turn signals on both sides were beginning to fail intermittently. I took the bulbs out to find that the contacts in the bulb housing were corroded and almost gone. As a temporary fix while waiting for the new bulb housing, I put aluminum foil between the housing and the bulbs.
r5SJHn. umpajg097k.pages.dev/396umpajg097k.pages.dev/321umpajg097k.pages.dev/379umpajg097k.pages.dev/225umpajg097k.pages.dev/52umpajg097k.pages.dev/530umpajg097k.pages.dev/129umpajg097k.pages.dev/418
bmw e46 indicators not working
